Comparative experimental studies of the operation process of the inertial planetary mechanism of screw conveyors

Authors

  • V. M. Karetin ТНТУ імені Івана Пулюя
  • P. D. Stukhliak Ivano-Frankivsk National Technical University of Oil and Gas, 15 Karpatska Street Ivano-Frankivsk Ukraine, 76019

DOI:

https://doi.org/10.31471/1993-9965-2020-2(49)-71-80

Keywords:

experimental stand, braking torque, rotation speed, gear ratio, inertial safety clutch, planned factorial experiment.

Abstract

The results of experimental studies of the technological process of the inertial safety clutch for two options and two cases of determining the braking torque of the output shaft: a combination with a reverse and a parasitic gear; combinations without reverse and  with parasitic gear; combinations with reverse and without parasitic gear; combinations without reverse and without parasitic gear are given. The functional nature of the change in the brake torque of the output shaft has been investigated. The plan of the factorial experiment was chosen, the limit intervals

or limit levels of variation (initial, or upper and final, or lower limit of change) of each individual input factor were set: the speed of the input shaft of the inertial safety clutch and the gear ratio. A histogram of non-approximated experimental data of the braking torque of the output shaft of the inertial safety clutch is constructed. On the basis of comparisons and analysis of graphical constructions of the diagram of the change in the braking torque of the output shaft of the inertial overload clutch for various combinations, it can be stated that: the process of operation of the inertial overload clutch using the reverse and with the parasitic gear provides a slight increase in the braking torque of the output shaft of the inertial overload clutch in on average by 3%; the process of operation of the inertial overload clutch without the use of reverse and with a parasitic gear practically does not provide an increase in the braking torque of the output shaft of the inertial overload clutch. On the basis of a comparative analysis, reasonably rational parameters of an inertial safety clutch at which its "stop" mode of operation is achieved.

Downloads

Download data is not yet available.

References

Klendii O.M. Obgruntuvannia parametriv zapobizhnykh muft hvyntovykh konveieriv. Dys. kand. tekhn. nauk: 05.02.02. Ternopil, 2015. 178 p. [in Ukrainian].

Hevko R.B., Klendii O.M. Pidvyshchennia nadiinosti funktsionuvannia hvyntovykh konveieriv. Visnyk Kharkivskoho natsionalnoho tekhnichnoho universytetu silskoho hospodarst-va imeni Petra Vasylenka. 2011. Vol. 114. P. 168-172. [in Ukrainian].

Malashhenko V. O., Malashhenko V.V., Shherbak V.V. Jeksperimental'nye issledovani-ja kojefficienta peredachi jenergii v zavisimosti ot induktivnoj nagruzki v soglasujushhem ustro-jstve diskovogo tipa. Avtomobil'nyj transport: sb. nauch. tr. HNADU. Har'kov, 2012. Vol. 31. P. 168-173.

Leonov A.I. Inercionnye avtomaticheskie transformatory vrashhajushhego momenta, Moskva: Mashinostroenie, 1978, 224 p. [in Russian].

Stukhliak P., Kurko A., Karetin V., Dobrotvor I. Analitychne doslidzhennia kinematyky debalansu reaktyvno-inertsiinoho bloka inertsiinoho transformatora krutnoho momentu. Mashynoznavstvo, 2011. No 7, P. 41-44. [in Ukrainian].

Berselli G. et al., Kinematic design and bond graph modeling of an inertia-type infinitely variable transmission, Proceedings of the ASME Design Engineering Technical Conference, 5, 2008, https://doi.org/10.1115/DETC2008-49875 .

Benitez F.G. et al. Infinitely Variable Transmission of Racheting Drive Type Based on One-Way Clutches, ASME. Journal of Mechanical Design. July 2004. 126(4). P. 673–682. https://doi.org/10.1115/1.1758258 .

Aliukov S. et al. Analysis of Methods for Solution of Differential Equations of Motion of Inertial Continuously Variable Transmissions, SAE Technical Paper, 2017, https://doi.org/10.4271/2017-01-1105.

Marchuk R., Komar R., Dubynyak T., Flonts O., Dynya V., Semeniv I. Substantiation of the parameters of hydraulic overload clutch. Scientific Journal of TNTU, 2017. Vol. 86, No 2, P. 59-66.

Lutsiv I., Hevko I., Dubynyak T., Manzii O. Defining parameters of elastic-safety clutches for screw conveyers. Scientific Journal of TNTU, 2017. Vol. 87, No 3, P. 72-80.

Liu K. et al. Dynamic Analysis of an Overrunning Clutch for the Pulse-Continuously-VariableSpeed Transmission, SAE Technical Paper, 1998, https://doi.org/10.4271/980827 .

Ince E. et al. On the advantages of the new power-split infinitely variable transmission over conventional mechanical transmissions based on fuel consumption analysis, Journal of Cleaner Production, 2020. https://doi.org/10.1016/j.jclepro.2019.118795 .

Tsuchiya E. et al. Formulation of intervibrator motion and development of a controller for a pulse-drive transmission, Mechanism and Machine Theory. Vol. 150. https://doi.org/10.1016/j.mechmachtheory.2020.103880.

Liang J. et al. Simulation Study on Planetary Bevel Gear CVT System Based on Virtual Prototyping Technology, Applied Mechanics and Materials. 215-216. 1003-1008 doi: https://doi.org/10.4028/www.scientific.net/AMM.215-216.1003.

Published

2020-12-30

How to Cite

Каретін, В. М., & Стухляк, П. Д. . (2020). Comparative experimental studies of the operation process of the inertial planetary mechanism of screw conveyors. Scientific Bulletin of Ivano-Frankivsk National Technical University of Oil and Gas, (2(49), 71–80. https://doi.org/10.31471/1993-9965-2020-2(49)-71-80