Determination of cam parameters of fixation node of the device for unscrewing of stuck pipes in the well

Authors

  • S. Yu Havryliv Ivano-Frankivsk National Technical University of Oil and Gas, 15 Karpatska Street Ivano-Frankivsk Ukraine, 76019
  • M. M. Liakh Ivano-Frankivsk National Technical University of Oil and Gas, 15 Karpatska Street Ivano-Frankivsk Ukraine, 76019
  • Yu. L. Havryliv Ivano-Frankivsk National Technical University of Oil and Gas, 15 Karpatska Street Ivano-Frankivsk Ukraine, 76019
  • R. O. Deineha Ivano-Frankivsk National Technical University of Oil and Gas, 15 Karpatska Street Ivano-Frankivsk Ukraine, 76019
  • V. V. Tyrlych Ivano-Frankivsk National Technical University of Oil and Gas, 15 Karpatska Street Ivano-Frankivsk Ukraine, 76019

DOI:

https://doi.org/10.31471/1993-9965-2020-2(49)-61-70

Abstract

Improvement of repair work efficiency in the elimination of drill pipe accidents  in a well is an extremely urgent task of oil field enterprises, and is achieved using special devices and tools. This paper analyses research and publications on this topic. The authors patented a device for unscrewing pipes in a well, in the fixation unit of which the use of a block of eccentric cams was proposed, and its experimental working model was made for research in a casing with a nominal diameter of D = 114 mm. The cycle of the device for unscrewing pipes in the well consists of three main periods: free running, jamming of the carrier of the device for unscrewing stuck pipes and the period of wedging. The article analyses operating conditions of the device fixation unit in the first two periods. The dependences of the power and geometric parameters of the device fixation unit on the angle of rotation of the cams are derived. Formulas are proposed for determining the force of pressing the cams against the casing during free travel, the moment of friction forces and power for this case. The dependence of the maximum permissible initial jamming angle on the friction coefficient and the geometric parameters of the device has been established. The lifting angle of the working surface of cams is determined. After substantiation of additional parameters of the block of cams to fulfill the condition of strength of its materials, it is planned to test a device for unscrewing pipes in an industrial environment in Factorial LLC, Poltava.

Downloads

Download data is not yet available.

References

Belousov A.P. Proektirovanie stanochnyih prisposobleniy: Uchebnoe posobie dlya uchaschihsya tehnikumov.3-e izd., pererab i dop.M.: Vyissh. Shkola, 1980. 240 p. [in Russian]

Anserov M.A. Zazhimnyie prisposobleniya dlya tokarnyih i krugloshlifovalnyih stankov. L.: Mashgiz, 1947. 181 p. [in Russian]

Goldin L.S. Dinamika zaklinivaniya mehanizmov svobodnogo hoda dvustoronnego deystviya. Peredatochnyie mehanizmyi.M.: Mashinostroenie, 1966. 215 p. [in Russian]

Levchuk K.H., Moisyshyn V.M., Rys V.V., Hural I.M. Mekhanichni sposoby vyvilnennia prykhoplenoho burylnoho instrumentu. Prykarpatskyi visnyk NTSh. Chyslo. 2017. No 2(38), P. 196-235. [in Ukrainian]

A.s. SSSR No 282218. Ustroystvo dlya otvorachivaniya trub v skvazhine. Opubl. 28.09.1970. Byul. No 30. [in Russian]

A.s. SSSR No 1146411. Ustroystvo dlya otvorachivaniya trub v skvazhine. Opubl. 23.03.1985. Byul. No 11. [in Russian]

A.s. SSSR No 1320387. Ustroystvo dlya otvorachivaniya trub v skvazhine. Opubl. 30.06.1987. Byul. No 24. [in Russian]

A.s. SSSR No 1352038. Ustroystvo dlya razvinchivaniya trub v skvazhine. Opubl. 15.11.1987. Byul. No 42. [in Russian]

A.s. SSSR No 1543042. Ustroystvo dlya otvorachivaniya burilnih trub v skvazhine. Opubl. 15.02.1990. Byul. No 6. [in Russian]

A.s. SSSR No 1559104. Ustroystvo dlya otvorachivaniya trub v skvazhine. Opubl. 23.04.1990. Byul. No 15. [in Russian]

A.s. SSSR No 1737100. Ustroystvo dlya otvorachivaniya trub v skvazhine. Opubl. 30.05.1992. Byul. No 20.

Prykhodko V.P. Proektuvannia osnashchennia verstativ, robotiv i mashyn [Elektronnyi resurs] : navchalnyi posibnyk dlia studentiv spetsialnosti 133 «Haluzeve mashynobuduvannia» spetsializatsii «Kompiuterne proektuvannia verstativ, robotiv i mashyn» / NTUU «KPI im. Ihoria Sikorskoho»; uklad.: Prykhodko V.P., Lytvyn O.V. Elektronni tekstovi dani (1 fail: 37,71 Mbait). Kyiv : NTUU «KPI im. Ihoria Sikorskoho», 2018. 211 p. [in Ukrainian]

Malashchenko V.O. i in. Kulkovi mekhanizmy vilnoho khodu. Lviv: Novyi svit-2000, 2012. 212 p. [in Ukrainian]

Pat. № 117766. Mekhanizm vilnoho khodu z separatorom. Opubl. 25.09.2018. Biul. No 18. [in Ukrainian]

Borys A.O. Pokrashchennia efektyvnosti mekhanichnykh pryvodiv zastosuvanniam kulkovykh obhinno-zapobizhnykh muft: dys. ... kand. tekhn. nauk: 05.02.02 - mashynoznavstvo. Lviv, 2019.170 p. [in Ukrainian]

Pat. No 45428. Prystrii dlia rozghvynchuvannia trub u sverdlovyni. Opubl. 15.04.2002. Biul. No 4. [in Ukrainian]

Pat. na korysnu model № 144078. Prystrii dlia rozghvynchuvannia trub u sverdlovyni. Opubl. 25.08.2020. Biul. No 16. [in Ukrainian]

Maltsev V.F. Rolikovyie mehanizmyi svobodnogo hoda. M.: Mashinostroenie, 1968. 416 p. [in Russian]

Korn G., Korn T. Spravochnik po matematike dlya nauchnyih rabotnikov i inzhenerov. M.: Nauka, 1974. 832 p. [in Russian]

Published

2020-12-30

How to Cite

Гаврилів, С. Ю. ., Лях M. M. ., Гаврилів, Ю. Л., Дейнега, Р. О., & Тирлич, В. В. . (2020). Determination of cam parameters of fixation node of the device for unscrewing of stuck pipes in the well. Scientific Bulletin of Ivano-Frankivsk National Technical University of Oil and Gas, (2(49), 61–70. https://doi.org/10.31471/1993-9965-2020-2(49)-61-70

Most read articles by the same author(s)